Biomechanical Research of Three Parallel Cannulated Compression Screws in Oblique Triangle Configuration for Fixation of Femoral Neck Unstable Fractures.

OBJECTIVE: Surgical treatment with internal fixation, specifically percutaneous fixation with three cannulated compression screws (CCSs), is the preferred choice for young and middle-aged patients. The mechanical advantage of the optimal spatial configuration with three screws provides maximum dispersion and cortical support. We suspect that the spatial proportion of the oblique triangle configuration (OTC) in the cross-section of the femoral neck isthmus (FNI) may significantly improve shear and fatigue resistance of the fixed structure, thereby stabilizing the internal fixation system in femoral neck fracture (FNF). This study aims to explore the mechanical features of OTC and provide a mechanical basis for its clinical application. METHODS: Twenty Sawbone femurs were prepared as Pauwels type III FNF models and divided equally into two fixation groups: OTC and inverted equilateral triangle configuration (IETC). Three 7.3 mm diameter cannulated compression screws (CCSs) were used for fixation. The specimens of FNF after screw internal fixation were subjected to static loading and cyclic loading tests, respectively, with five specimens for each test. Axial stiffness, 5 mm failure load, ultimate load, shear displacement, and frontal rotational angle of two fragments were evaluated. In the cyclic loading test, the load sizes were 700 N, 1400 N, and 2100 N, respectively, and the fracture end displacement was recorded. Results were presented as means ± SD. Data with normal distributions were compared by the Student's t test. RESULTS: In the static loading test, the axial stiffness, ultimate load, shear displacement, and frontal rotational angle of two fragments were (738.64 vs. 620.74) N/mm, (2957.61 vs. 2643.06) N, (4.67 vs. 5.39) mm, and (4.01 vs. 5.52)° (p < 0.05), respectively. Comparison between the femoral head displacement after 10,000 cycles of 700N cyclic loading and total displacement after 20,000 cycles of 700-1400N cyclic loading showed the OTC group was less than the IETC group (p < 0.05). A comparison of femoral head displacement after 10,000 cycles of 1400N and 2100N cycles and total displacement after 30,000 cycles of 700-2100N cycles showed the OTC group was less than another group, but the difference was not significant (p > 0.05). CONCLUSION: When three CCSs are inserted in parallel to fix FNF, the OTC of three screws has obvious biomechanical advantages, especially in shear resistance and early postoperative weight-bearing, which provides a mechanical basis for clinical selection of ideal spatial configuration for unstable FNF.

ASCC3 promotes the immunosuppression and progression of non-small cell lung cancer by impairing the type I interferon response via CAND1-mediated ubiquitination inhibition of STAT3.

BACKGROUND: Activating signal cointegrator 3 (ASCC3) has been identified as an oncogenic factor that impairs host immune defense. However, the underlying mechanisms of carcinogenesis and its impact on the antitumor immune response remain unclear. In this study, we aimed to investigate the molecular mechanisms of ASCC3 in the progression of non-small cell lung cancer (NSCLC). METHODS: Single-cell sequencing data from the Gene Expression Omnibus and gene expression profiles from The Cancer Genome Atlas database were analyzed. The expression, clinical relevance and biological functions of ASCC3 in NSCLC were explored. Then, RNA sequencing, immunoprecipitation, mass spectrometry, immunofluorescence, and flow cytometry analyses were conducted to explore the underlying molecular mechanisms. In addition, in vivo experiments in mouse models were conducted to explore the probability of ASCC3 knockdown to improve the efficacy of anti-Programmed Death-1 (PD-1) therapy in NSCLC. RESULTS: ASCC3 was significantly upregulated in NSCLC and correlated with poor pathological characteristics and prognosis in patients with NSCLC. Overexpression of ASCC3 promoted malignant phenotypes of NSCLC cells and induced an immunosuppressive tumor microenvironment, which was characterized by a decrease in CD8+ T cells, natural killer cells and dendritic cells but an increase in regulatory T(Treg) cells. Mechanistically, ASCC3 stabilized signal transducer and activator of transcription (STAT)3 signaling by recruiting Cullin-associated and neddylation dissociated 1 (CAND1), which inhibited ubiquitin-mediated degradation of STAT3, thereby impairing the type I interferon response of tumor cells and promoting the immunosuppression and progression of NSCLC. Furthermore, high expression of ASCC3 impaired the efficacy of anti-PD-1 therapy, and an anti-PD-1 antibody combined with ASCC3 knockdown exerted promising synergistic efficacy in a preclinical mouse model. CONCLUSION: ASCC3 could stabilize the STAT3 pathway via CAND1, reshaping the tumor microenvironment and inducing resistance to anti-PD-1 therapy, which promotes the progression of NSCLC. It is a reliable prognostic indicator and can be a target in combination therapy for NSCLC.

Intramedullary nailing versus plating fixation for the treatment of midshaft clavicular fractures: A meta-analysis of randomized controlled trials.

PURPOSE: This study was to test the hypothesis that intramedullary (IM) nailing fixation of midshaft clavicle fractures could result in better clinical outcomes and lower complications rates than plating fixation. METHODS: PubMed, Embase, and the Cochrane Library database were used to search all English language published randomized controlled trials (RCTs) of midshaft clavicle fractures using plating versus IM nailing. The characteristics of the study participants were collected. Outcomes of postoperative shoulder functional measurements, operative data and complications rates were meta-analyzed. RESULTS: Eight hundred and ninety-five patients in ten RCTs and three quasi-RCTs were involved in the meta-analysis. The results of meta-analysis of these studies showed that the functional outcome evaluated by the Constant Shoulder and Disabilities of the Arm, Shoulder and Hand (DASH) scores after accepting IM nailing was significantly better than that of plating fixation at one year post-operatively (P < 0.01), with the heterogeneity of 43% and 91%, respectively. Sensitivity analyses of the pooled results of Constant and DASH scores displayed that the functional advantage of IM nailing fixation comes from the subgroup of locked IM nailing. Further, regarding the operative statistics, operative time, blood loss and wound length were significantly less in the IM nailing group than the plating group (P < 0.001). The rates of infection, major complications and complications-related revision surgery were significantly higher in the plating group than the IM nailing group; however, there were no significantly statistical differences in other complications, e.g., nonunion, refracture after hardware removal, implant failure, symptomatic hardware, etc. (P > 0.05). CONCLUSION: The observations in this review suggested that IM nailing, especially locked IM nailing, could provide better shoulder functional outcome at one-year follow-up. Moreover, IM nailing fixation could effectively reduce operative time, blood loss, rates of infection, major complications, and revision surgery than plating. Further high-quality clinical trials with large samples and consistent designs are still needed to verify the long-term functional advantage of locked and unlocked IM nailing for midshaft clavicle fractures. LEVEL OF EVIDENCE: Level II.

The oblique triangle configuration of three parallel screws for femoral neck fracture fixation using computer-aided design modules.

Closed reduction and internal fixation with three cannulated compression screws is a common method for treating femoral neck fractures in young and middle-aged patients. Protocols including the inverted triangle configuration and dispersion of the screws still needed further supports. The purpose of this study was to explore a novel oblique triangle configuration (OTC) of three screws in fixing femoral neck fractures based on the morphology of the femoral neck isthmus (FNI). The computer-aided design modules were used to explore the ideal spatial configuration with largest triangle by three parallel screws. A univariate evaluation model was established based on the oval-like cross-section of the FNI. When the three screws were positioned by the OTC, Inverted Equilateral Triangle Configuration (IETC), and the Maximum Area Inverted Isosceles Triangle Configuration (MA-IITC) respectively, the proportion of area and circumference in the cross-section of FNI and the changing trend of proportion were compared under various torsion angles, eccentricity, and cross-sectional area of FNI. The area and circumference ratios of the parallel screws using the OTC method were significantly higher than in the IETC and MA-IITC groups. In the univariate evaluation model, the OTC area ratio and circumference ratio remained stable under the different femoral neck torsion angles, FNI cross-sectional area, and eccentricity. The OTC method provided an ideal spatial configuration for the FNA fixation with the largest area using three parallel screws. The position of the posterior screw was also away from the metaphyseal artery, potentially reducing the possibility of vascular injury and screw penetrating.

Comparison of oblique triangular configuration and inverted equilateral triangular configuration of three cannulated screws in treating unstable femoral neck fracture: A finite element analysis.

BACKGROUND: The cross-sectional area of three parallel screws might affect the stability of the internal fixation of femoral neck fractures. The screws fixed in the oblique-triangle configuration (OTC) were assumed to have a larger cross-sectional area, but the biomechanical stability has not yet been validated. In this study, finite element analyses were performed to compare the biomechanical properties of the internal fixation fixed by the OTC and the traditional Inverted Equilateral Triangle Configuration (IETC). METHOD: Pauwels type III fracture was established on the three-dimensional femoral model and three cannulated screws with the OTC and traditional IETC methods were applied. The oblique-triangle configuration with the largest area inscribed the femoral neck isthmus by the three screws was determined, the area and circumference of the cross-section formed by the OTC and IETC model were compared. Stress, strain, and displacement peaks of the two configuration models under different loads were compared. Twelve pairs of nodes on the fracture ends were selected and the displacement of the fracture ends was evaluated through the displacement between these nodes. RESULTS: The area and circumference of the cross-section formed by the OTC were larger than those in the IETC model. The degree of stress dispersion around the screw holes in the OTC model was better than that of the IETC, but the stress distribution order of the three screws in the two models was consistent. The maximum stress, strain, displacement, and displacement of the fracture end in the OTC model were smaller than those in the IETC model. The stress, strain, displacement, and fracture end displacement peaks of the two fixed models gradually increase with the increase of loads. CONCLUSION: The oblique-triangle configuration showed superior mechanical properties than the IETC in finite element analyses. This study suggests that when three screws are fixed in parallel method, the larger the cross-sectional area of the screw configuration, the better stability of the internal fixation might be obtained. Furthermore, the biomechanical properties of various spatial configurations and screw holes of the three parallel screws need to be considered before clinical practice.

The Oval-like Cross-section of Femoral Neck Isthmus in Three-dimensional Morphological Analysis.

OBJECTIVES: To investigate the cross-section shape of the femoral neck isthmus (FNI) in three-dimensional reconstruction model of the femoral neck. METHODS: From December 2009 to December 2012, computed tomography (CT) data of bilateral hip joint from 200 consecutive patients (137 males and 63 females, 69.41 ± 9.21 years old, ranged from 50-85 years old) who underwent surgical treatments for proximal femoral fracture were retrospectively reviewed. The 3D model of the proximal femur was reconstructed, and the "inertia axis" method, which was applied to measure the long and short axes of the cross-section of the FNI, was established. The cross-sectional area and perimeter were calculated by a formula using the length of the long and short axes and then compared with the actual measured values by the software. Correlation between the descriptive parameters of the FNI cross-section (area, perimeter, and eccentricity) and patients' demographics (age, height, and weight) was analyzed. Stepwise linear regression analysis was used to determine the main relevant factors. RESULTS: The ICC results showed excellent data reproducibility ranged from 0.989 to 0.996. There was no significant difference in the cross-sectional area of the FNI between the actual measured values and the predicted values using the formula (732.83 ± 126.74 mm2 vs 731.62 ± 128.15 mm2 , P = 0.322). The perimeter using the two methods showed narrow while significant difference (97.86 ± 8.60 mm vs 92.84 ± 8.65 mm, P < 0.001), the actual measured values were about 5 mm greater than the predicted values. The parameters (area, perimeter, and eccentricity) were significantly larger in male than female (P < 0.001). A positive correlation between the cross-sectional area, perimeter, height, and weight was observed. The stepwise linear regression analysis showed that the regression equation of the FNI area was as follows: Y = -1083.75 + 1033.86 × HEIGHT + 1.92 × WEIGHT, R2 = 0.489. CONCLUSION: The cross-section shape of the FNI appears to be oval-like in the 3D model, which is separated according to the inertia axis, and the findings proposed an anatomical basis for the further study of the spatial configuration of cannulated screws in the treatment of femoral neck fractures.

Epidural electrical stimulation effectively restores locomotion function in rats with complete spinal cord injury.

Epidural electrical stimulation can restore limb motor function after spinal cord injury by reactivating the surviving neural circuits. In previous epidural electrical stimulation studies, single electrode sites and continuous tetanic stimulation have often been used. With this stimulation, the body is prone to declines in tolerance and locomotion coordination. In the present study, rat models of complete spinal cord injury were established by vertically cutting the spinal cord at the T8 level to eliminate disturbance from residual nerve fibers, and were then subjected to epidural electrical stimulation. The flexible extradural electrode had good anatomical topology and matched the shape of the spinal canal of the implanted segment. Simultaneously, the electrode stimulation site was able to be accurately applied to the L2-3 and S1 segments of the spinal cord. To evaluate the biocompatibility of the implanted epidural electrical stimulation electrodes, GFAP/Iba-1 double-labeled immunofluorescence staining was performed on the spinal cord below the electrodes at 7 days after the electrode implantation. Immunofluorescence results revealed no significant differences in the numbers or morphologies of microglia and astrocytes in the spinal cord after electrode implantation, and there was no activated Iba-1+ cell aggregation, indicating that the implant did not cause an inflammatory response in the spinal cord. Rat gait analysis showed that, at 3 days after surgery, gait became coordinated in rats with spinal cord injury under burst stimulation. The regained locomotion could clearly distinguish the support phase and the swing phase and dynamically adjust with the frequency of stimulus distribution. To evaluate the matching degree between the flexible epidural electrode (including three stimulation contacts), vertebral morphology, and the level of the epidural site of the stimulation electrode, micro-CT was used to scan the thoracolumbar vertebrae of rats before and after electrode implantation. Based on the experimental results of gait recovery using three-site stimulation electrodes at L2-3 and S1 combined with burst stimulation in a rat model of spinal cord injury, epidural electrical stimulation is a promising protocol that needs to be further explored. This study was approved by the Animal Ethics Committee of Chinese PLA General Hospital (approval No. 2019-X15-39) on April 19, 2019.

[Biomechanical study on the treatment of intertrochanteric fracture of A3.3 type with medial sustainable nail and proximal femoral anti-rotation nail].

OBJECTIVE: A3 intertrochanteric fracture is an extremely unstable fracture, which is often treated with intramedullary nail, but the implant failure is common due to the posterior medial fragment cannot be reconstructed. A new medial sustainable nail (MSN-Ⅱ) which can reconstruct the femoral medial support by sustainable screw was introduced in this study. The mechanical effect was verified by biomechanical experiment. METHODS: The loss medial support model of intertrochanteric fracture (A3) was made by artificial Sawbones model, fixed with MSN-Ⅱ and PFNA-Ⅱ, underwent axial loading and axial failure tests. The axial stiffness, yield load, displacement of head-neck fragment and torsional angle of fracture site of these nails were recorded and compared for biomechanical differences. The effect of early reconstruction of medial support with MSN-Ⅱ was determined. RESULTS: The axial stiffness, yield load, the displacement of head and neck fragment when the axial load was 1 800 N and torsional angle of the fracture site after the axial failure test of MSN-Ⅱ were (222.76 ±62.46) N /mm, (4 241.71 ±847.42) N, (11.51 ±0.62) mm, (1.71 ±0.10)° respectively, while the PFNA -Ⅱ was (184.58±40.59) N /mm, (3 058.76±379.63) N, (16.15±1.36) mm, (2.52±0.26)°respectively. The difference between the two groups was statistically significant. CONCLUSION: The axial stiffness of MSN-Ⅱ is better than that of PFNA-Ⅱ. The MSN-Ⅱ can bear more loads when fixed A3.3 intertrochanteric fracture and has greater axial and rotational stability. It is an effective means to reconstruct the medial support of A3 intertrochanteric fracture.

A Hybrid Uniplanar Pedicle Screw System with a New Intermediate Screw for Minimally Invasive Spinal Fixation: A Finite Element Analysis.

PURPOSE: A hybrid pedicle screw system for minimally invasive spinal fixation was developed based on the uniplanar pedicle screw construct and a new intermediate screw. Its biomechanical performance was evaluated using finite element (FE) analysis. METHODS: A T12-L2 FE model was established to simulate the L1 vertebral compression fracture with Magerl classification A1.2. Six fixation models were developed to simulate the posterior pedicle screw fracture fixation, which were divided into two subgroups with different construct configurations: (1) six-monoaxial/uniplanar/polyaxial pedicle screw constructs and (2) four-monoaxial/uniplanar/polyaxial pedicle screw constructs with the new intermediate screw. After model validation, flexion, extension, lateral bending, and axial rotation with 7.5 Nm moments and preloading of 500 N vertical compression were applied to the FE models to compare the biomechanical performances of the six fixation models with maximum von Mises stress, range of motion, and maximum displacement of the vertebra. RESULTS: Under four loading scenarios, the maximum von Mises stresses were found to be at the roots of the upper or lower pedicle screws. In the cases of flexion, lateral bending, and axial rotation, the maximum von Mises stress of the uniplanar screw construct lay in between the monoaxial and polyaxial screw constructs in each subgroup. Considering lateral bending, the uniplanar screw construct enabled to lower the maximum von Mises stress than monoaxial and polyaxial pedicle screw constructs in each subgroup. Two subgroups showed comparable results of the maximum von Mises stress on the endplates, range of motion of T12-L1, and maximum displacement of T12 between the corresponding constructs with the new intermediate screw or not. CONCLUSIONS: The observations shown in this study verified that the hybrid uniplanar pedicle screw system exhibited comparable biomechanical performance as compared with other posterior short-segment constructs. The potential advantage of this new fixation system may provide researchers and clinical practitioners an alternative for minimally invasive spinal fixation with vertebral augmentation.

Medial support nail and proximal femoral nail antirotation in the treatment of reverse obliquity inter-trochanteric fractures (Arbeitsgemeinschaft fur Osteosynthesfrogen/Orthopedic Trauma Association 31-A3.1): a finite-element analysis.

BACKGROUND: The reverse obliquity inter-trochanteric fracture is a distinct fracture pattern that is mechanically different from most inter-trochanteric fractures and the optional treatment of it is still controversial. The purpose of this study was to compare differences in the efficacy of a novel nail (medial support nail [MSN-II]) and proximal femoral nail anti-rotation (PFNA-II) in the treatment of reverse obliquity inter-trochanteric fractures (Arbeitsgemeinschaft fur Osteosynthesfrogen/Orthopedic Trauma Association [AO/OTA] 31-A3.1) using finite-element analysis. METHODS: Modeling software was used to establish a three-dimensional model of MSN-II and PFNA-II and an A3.1 inter-trochanteric fracture model. Abaqus software was used to implement different force loads to compare finite-element biomechanical parameters such as the maximum stress in implant and the displacement of fracture site. RESULTS: The femoral stress, implant stress and fracture site displacement of MSN-II was less than that of PFNA-II. The results indicated that the maximal femoral stress was 581 MPa for PFNA-II and 443 MPa for the MSN-II. The maximum stress values in the PFNA-II and MSN-II models were 291 and 241 MPa, respectively. The maximal displacements of the fracture site were 1.47 and 1.16 mm in the PFNA-II and MSN-II models, respectively. CONCLUSION: Compared with PFNA-II for inter-trochanteric fracture (AO/OTA 31-A3.1), MSN-II which was designed with a triangular stability structure can provide better biomechanical stability. The MSN-II may be a feasible option for the treatment of reverse obliquity inter-trochanteric fracture.

Erratum to radiographic assessment of the cup orientation after total hip arthroplasty: a literature review.

[This corrects the article DOI: 10.21037/atm.2019.12.150.].

Three-dimensional morphological analysis of the femoral neck torsion angle-an anatomical study.

BACKGROUND: The femoral neck torsion angle (FNTA) is an important but often neglected parameter in assessments of the anatomical morphology of the femoral neck, which is often confused with the femoral neck anteversion angle (FNAA) in the current literature. Currently, the measurement methods reported in the literature all adopt the naked eye or two-dimensional (2D) visualization method, and the measurement parameters and details are not clearly defined. The objection of this research was to provide a reliable 3D method for determining the femoral neck axis, to improve the measurement method of the FNTA, and to analyze the anatomical and clinical significance of the results. METHODS: Computed tomography (CT) data of 200 patients who received a lower extremity CT angiography examination were selected, and the bilateral femurs were reconstructed with three dimensional CT (3D CT). First, the 3D axis of the femoral neck was built. Second, the long axis of the cross section the femoral neck isthmus (FNI) and femoral neck basilar part (FNB) were confirmed by the "inertia axes" method, and the plane consisting of the long axis of the cross-section and the center of the femoral head was defined as the long axial plane. Third, the coronal plane of the proximal femur was determined through the long axis of the proximal femur and the femoral coronal. Finally, the FNTAs (the angles between the long axial planes and the coronal plane of the proximal femur) of FNI and FNB were measured. The size of FNTA was compared between the sexes and sides and different locations, the correlation between the parameters and age, height, and weight were evaluated. RESULTS: The difference in FNTA was statistically significant between the isthmus and the basilar part (isthmus 30.58 ± 8.90° vs. basilar part 23.79 ± 3.98°; p < 0.01). Significant difference in the FNTA was observed between the sexes (males 31.99 ± 9.25° vs. females 27.49 ± 7.19°; p < 0.01). The increase in FNTA from the basilar part to the isthmus was 6.79 ± 8.06°, and the male (7.87 ± 8.57°) was greater than the female (4.44 ± 6.23°, p < 0.01). However, no significant difference in the values was observed between sides. Height exerted the greatest effect on the FNTA according to the correlation analysis (r = 0.255, p< 0.001). CONCLUSIONS: This study found a reliable 3D method for the determination of the femoral neck axis improved the measurement method of the FTNTA and made it more accurate and repeatable. The results provided a methodological basis and theoretical support for the research and development of internal fixation device for femoral neck fracture and the spatial configuration of implants in treatment. And the optimal opening point of the femoral medullary cavity was recommended to locate at the posterior position of the top of the femoral neck cross-section during hip replacement.

Radiographic assessment of the cup orientation after total hip arthroplasty: a literature review.

Optimal acetabular cup orientation is of substantial importance to good long-term function and low complication rates after total hip arthroplasty (THA). The radiographic anteversion (RA) and inclination (RI) angles of the cup are typically studied due to the practicability, simplicity, and ease of interpretation of their measurements. A great number of methods have been developed to date, most of which have been performed on pelvic or hip anteroposterior radiographs. However, there are primarily two influencing factors for these methods: X-ray offset and pelvic rotation. In addition, there are three types of pelvic rotations about the transverse, longitudinal, and anteroposterior axes of the body. Their effects on the RA and RI angles of the cup are interactively correlated with the position and true orientation of the cup. To date, various fitted or analytical models have been established to disclose the correlations between the X-ray offset and pelvic rotation and the RA and RI angles of the cup. Most of these models do not incorporate all the potential influencing parameters. Advanced methods for performing X-ray offset and pelvic rotation corrections are mainly performed on a single pelvic AP radiograph, two synchronized radiographs, or a two-dimensional/three-dimensional (2D-3D) registration system. Some measurement systems, originally developed for evaluating implant migration or wear, could also be used for correcting the X-ray offset and pelvic rotation simultaneously, but some drawbacks still exist with these systems. Above all, the 2D-3D registration technique might be an alternative and powerful tool for accurately measuring cup orientation. In addition to the current methods used for postoperative assessment, navigation systems and augmented reality are also used for the preoperative planning and intraoperative guidance of cup placement. With the continuing development of artificial intelligence and machine learning, these techniques could be incorporated into robot-assisted orthopaedic surgery in the future.

Evolution and Current Applications of Robot-Assisted Fracture Reduction: A Comprehensive Review.

Robots in orthopedic surgery have been developed rapidly for decades and bring significant benefits to the patients and healthcare providers. However, robotics in fracture reduction remains at the infant stage. As essential components of the current robotic system, external fixators were used in fracture reduction, including the unilateral and Ilizarov-like ring fixators. With emerging of the industrial robots and mechanical arms, their sterilized variants were developed as the serial robots, including the traction device and robotic arm, for fracture reduction. Besides, parallel robots (e.g., Gough-Stewart platform) were devised for lower extremity traction and fracture reduction. After combining the advantages of the serial and parallel mechanisms, hybrid robots can fulfill specific clinical requirements (e.g., the joint fracture, including multiple major fragments). Furthermore, with the aid of intra-operative navigation systems, fracture reduction can be performed under real-time guidance. The paper presents a comprehensive overview of the advancement of the robots in fracture reduction and evaluates research challenges and future perspectives, including ergonomic and economic issues, operation time, artificial realities and intelligence, and telesurgery.

Three-dimensional mapping of intertrochanteric fracture lines.

BACKGROUND: Available research about the anatomic patterns of intertrochanteric fractures is lacking, and fracture mapping has not previously been performed on intertrochanteric fractures. This study aimed to determine the major trajectories of intertrochanteric fracture lines using computed tomography data from a series of surgically treated patients. METHODS: In this study, 504 patients with intertrochanteric fractures were retrospectively analyzed. Fracture patterns were graded according to Arbeitsgemeinschaft für Osteosynthesefragen (AO) classification. Fracture lines were transcribed onto proximal femoral templates and graphically superimposed to create a compilation of fracture maps that were subsequently divided into anterior, posterior, lateral, and medial fracture maps to create a three-dimensional (3D) pattern by reducing fragments in the 3D models. The fracture maps were then converted into frequency spectra. The major fracture patterns were assessed by focusing on the lateral femoral wall, lesser trochanter, intertrochanteric crest, and inner cortical buttress. RESULTS: Anterior, posterior, lateral, and medial fracture maps were created. The majority of fracture lines (85.9%, 433/504) on the anterior maps were along the intertrochanteric line where the iliofemoral ligament was attached. In the medial plane, the majority of fracture lines (49.0%, 247/504) shown on the frequency spectrum included the turning point involving the third quadrant. In the posterior plane, the majority of fracture lines (52.0%, 262/504) involved the intertrochanteric crest from the greater to the lesser trochanter. In the lateral plane, the majority of fracture lines (62.7%, 316/504) involved the greater trochanter at the gluteus medius attachment. CONCLUSIONS: The fracture patterns observed in the present study might be used to describe morphologic characteristics and aid with management strategies. Further classifications or modifications that incorporate the fracture patterns identified in this study may be used in future research.

The synergetic effect of pelvic rotation and X-ray offset on radiographic angles of the acetabular cup.

The objective of this study is to investigate the synergetic effect of the pelvic rotation and X-ray offset on the radiographic anteversion/inclination (RA/RI) angles of the acetabular cup using a mathematical model. A cone model for establishing the spatial relationship between a three-dimensional (3D) circle and its two-dimensional (2D) elliptical projection is utilized to quantify the relationship between the 3D RA/RI angles of the cup and their 2D counterparts with different types of pelvic rotations in pelvic/hip anteroposterior radiographs. The results reveal that the effect of inlet/outlet views on the 2D RA angle is similar to that of iliac/obturator views. The permissible ranges of pelvic rotation for the 2D RA angle with an acceptable bias are the 3D space formed by the limits of triple axial rotations. For a specified acceptable bias of the 2D RA angle, these ranges are almost equal between pelvic and hip radiographs. The combined inlet/obturator or outlet/iliac views can maintain the 2D RA angle of a pelvic radiograph within the same range of acceptable bias as that of a hip radiograph. For a 2D RA angle with an acceptable bias, the permissible range of pelvic rotation needs to be evaluated with equal attention in both radiographs. Graphical abstract The traditional methods for calculating the radiographic angles of the acetabular cup are based on the ellipse projection of the opening circle of the cup on radiographs. However, with varying locations of the X-ray source and pelvis rotations about different axes, the outline of this ellipse projection will change, and accordingly, the traditional method and calculating results will be inaccurate. In this study, a cone model for three-dimensional circle-to-two-dimensional ellipse projection is utilized to incorporate the effect of X-ray offset and quantify the relationships of the radiographic angles of the cup with the true orientation of the cup and pelvic rotations in either pelvic or hip anteroposterior radiographic situation.

Differences in Bone Mineral Density and Hip Geometry in Trochanteric and Cervical Hip Fractures in Elderly Chinese Patients.

OBJECTIVE: To assess the differences in bone mineral density (BMD) and hip geometry in trochanteric and cervical hip fractures in elderly Chinese patients. METHODS: A consecutive series of 196 hip fracture patients aged over 50 years was recruited from November 2013 to October 2015, including 109 cases of cervical fractures (36 males and 73 females) and 87 cases of trochanteric fractures (34 males and 53 females). All patients were evaluated through dual-energy X-ray absorptiometry, and baseline characteristics, BMD and structural parameters were collected and reviewed. RESULTS: There were statistically significant differences in age, height, and body mass index between patients with each type of fracture, and patients with trochanteric fractures were older than those with cervical fractures, especially in women. The BMD in trochanteric fractures was markedly lower than in cervical fractures in all five sites of the hip by an approximate reduction of 10%, in both men and women. The cross-sectional area, cross-sectional moment of inertia, and the cortical thickness in the cervical fracture group were significantly higher than in the trochanteric fracture group. However, the buckling ratio of both the femoral neck and trochanteric region were significantly lower in the cervical fracture group. Age (/10 years), cross-sectional moment of inertia in femoral neck and buckling ratio in trochanteric region were significant risk factors for trochanteric fractures compared with cervical fractures. CONCLUSIONS: Compared with cervical hip fractures, patients with trochanteric fractures were older, had a lower BMD, and had less bone mechanical strength, especially in female patients. Age, femoral neck cross-sectional moment of inertia (FNCSMI), and trochanteric region buckling ratio (ITBR) were stronger risk factors for trochanteric hip fractures than for cervical fractures.